Aluminium Extrusion Handling System for 1450ust Press

Aluminium Extrusion Handling System for 1450ust Press

one. Picture 

Aluminium handing table for 1450UST Press(6 inch billet) with 4 BELT Type dismantle variety (Belt can be modified separately)

Operational side will be confirmed by the last structure drawing.

two. Parameters

Overall performance and parameter Need
Press dimensions 1450UST
Get quantity 1
Duration of direct out desk 10m
Duration of handing desk 32m
Spacing 1200mm
Max bearing potential 8kg/m
Table attribute Run out table and storage table : CZPT lifting type.
 Handing desk : Four BELT Type, dismantle. Every belt is able to adjust individually.
Max fat of profile 8kg/m
Max dimension of profile 150×140mm
All round dimension of table(L*W*H) Length 32m x Width 7m x Height 850mm

three. Major framework

one) Direct Out Table :
Dimension: Size : 10000mm * Width:500mm * Peak:850mm
    PBO3+seven felt roller (idle): Ф76 / 96 * 400mm     Temperature : 600ºC     Spacing : 400mm

two) Cooling blower:
    On best of guide out table :
2 sets centrifugal blower equipment, 6M long / established .
    Below lead out desk : ten sets of cooling supporters, .55kw/established
    Underneath the cooling table : ten sets of cooling enthusiasts. Front density and rear sparse. Separately manage in two groups.

3) CZPT Lifting Table :
    Length : 32000mm * Width : 500mm * Peak : 850mm
    Configuration : 4mm thickness and 300m width bending sheet .

    Higher temperature resistant felt roller : Ф76 / 96 *400mm   Temperature : 480 ºC , Gap : 400mm
    Doing work System : Rollers are totally powered by chain to go up/down. The roller speed need to adjust to synchronize with extrusion velocity by using inverter (AC Driver) .
    With hydraulic lifting stage one set.  Lifting Height : 50mm
    Transmission electrical energy machine : Cycloid pin , .55 Kw * three sets

four) CZPT Belt:
    Duration : 32000mm * Width : 715mm * Top : 850

    High temperature felt strap transmission : Thickness : 10mm * Width : 80mm
   Temperature : 480ºC , 27 pieces   
   Control : Cycloid pin electrical device : 3Kw , 1 set

five) Cooling Desk:
    Size : 32000mm * Width : 2600mm * Top : 850mm

    High temperature felt strap transmission : Thickness : 10mm * Width : 80mm
    Temperature : 480ºC, 27pieces
    Management : Cycloid pin electrical machine : three Kw , one set

six) Stretcher Feeding Desk:
    Size : 32000mm * Width : 1600mm * Peak : 850mm
    Medium temperature felt strap transmission : Thickness : 10mm * Width : 80mm
    Temperature : 280ºC, 27pieces
    Control : Cycloid pin electrical device : three Kw , 1 set
    The belt must be powered by pneumatic placement.

7) Storage Table :
    Length : 30000mm * Width :2100mm* Height : 850mm
   Low temperature felt strap transmission : Thickness : 10mm * Width : 80mm
   Temperature : 180ºC , 27 pieces
   Control : Cycloid pin electrical equipment : 3 Kw , 1 set

eight) Saw Content Desk :
    Duration : 32000mm * Width : 700mm * Peak : 850mm.

    Minimal temperature resistant felt roller : Ф76 / 96* 800mm    Temperature : 180ºC  Gap : 400mm
    Working System : Rollers are entirely run by partial chain and moves up / down .The roller speed need to be use inverter(AC Driver) to alter in buy to need.

     Transmission CZPTal machine: .75 KW    three sets

nine) Observed Gauge Desk(computerized ) :
    Length : 8000mm * Width : 600 * Peak : 850mm

    Minimal temperature resistant felt roller : Ф76 / 96* 800mm Temperature : one hundred eighty C Gap : 400mm
    Lifting height : 50 cm.
    Cycloid pin electrical machine : .seventy five Kw , one established
    Chopping range from 1-eight m

ten) Stretcher: (one particular man stretcher )
    Pulling power : four Tons. Design of clamp ora : clamped and swerved by hydraulic driving. The back jaw have to be pushed all by hydraulic method on its track. Motion of the stretcher shall be controlled by a motor .

eleven) Finishing Observed Desk:
    Diameter of blade : 450mm     Run-size of blade: 750mm

    Dimension of attainable reducing : Width : 500mm * Top : 130mm
    Control : PLC or manual , siclon for collecting the burs at finish observed. With chips collector

12) Material Sending Belts : eight000mm * 2000mm* Peak:820mm.
    Size : 4600mm * Width : 80mm * Thickness 10mm
   Transmission by lower temperature resistant felt belts.     
   Temperature : 180 C         Gap: 1200mm      
   Number of belts : seven pcs
   Transmission CZPTal machine: .55 KW 1 established

4. Our Firm

HangCZPT Yesheng CZPT & Export Co.,Ltd. is largely engaged in providing aluminium processing equipment these kinds of as steady caster, chilly mill, foil mill, tension leveler, reduce-to-size line, slitting line, foil doubling machine, coloration coating line, degasser and filter, plate filter, circle blanking line, foil container manufacturing line, slab caster, slab milling machine, slab noticed, melting furnace, holding furnace, annealing furnace, growing older furnace, metal spool, work roll, backup roll, caster roll, and caster suggestion and many others. and the spare elements for the over tools. And we also source extrusion line this sort of as push, tunnel furnace, dealing with equipment, DC caster, homogenizing furnace, anodizing line, powder coating line and many others.

China make tools are extremely common all more than the entire world specially in south east Asia, African nations, South The us, Middle East largely since of affordable price and excellent top quality. Nevertheless, for each equipment there are a lot of companies. Some are trustworthy and some are not. Most of clients are perplexed and never know which suppliers are reputable. My company’s primary enterprise is to aid these buyers discover dependable suppliers for any equipment with great high quality, realistic cost and best following -sale companies.

5. Services Assurance

one. Provide 24-hour technological help by email or cellphone.
2. Supply expert solutions suitable for the generation line, in accordance to the specifications of client investment decision and generation potential,
3. Give spare parts checklist
4. Give basis format and structure for the manufacturing unit
5. Assign specialist engineers to the website to information the installation and commissioning, according to the customer’s needs till the final merchandise fulfills the customer’s requirements.
six. Supply great soon after-product sales services, extended-term real-time monitoring of user’s area products use, and supply well timed and efficient existence-long support for consumers.
7. If you want to alter the creation line, build new products or improve tools, we will supply prolonged-expression complex providers.

Aluminium Extrusion Handling System for 1450ust Press